This automatic optical fiber tensile testing program is ideal for operator skill independent use in production and laboratory settings. Two basic model configurations permit the consumer to select between a set up for standard linear proof testing with additional mandrels for rotary high strength testing.
The linear edition is ideal for creation proof screening with forces approximately 22 N. Motor-driven clamps with carefully developed rubber inserts ensure that the Sheathing Line is not really ruined inside the screening process while at the same time eliminating the requirement for another air provide. Amounts of pulling force, tugging speed and hold time are programmable and easily available to the operator with the built-in LCD touchscreen display control. Data from assessments can be stored and reached through the USB dock or Ethernet interface.
Mandrels the exact same style as in NYFORS’ optical fiber recoaters can be mounted on the proof tester within the rotary higher power settings. The fiber is wrapped across the two mandrels which assistance it having a special clamping system. In this way higher loads can be applied on the fiber, allowing breaking strength assessments under managed conditions.
Adjustable clamp placement facilitates testing with the highest force levels as well as testing of short fiber measures. The lightweight and light bodyweight design helps make the instrument easy to move around in a lab environment and to incorporate in a creation work bench in which space are at a premium. The machine is actually a lightweight and lightweight tool perfect for screening the effectiveness of optical materials approximately 30 N. The equipment is designed to meet all types of applications in which a power check must be performed.
The equipment is designed with the user in mind. The Fiber Drawing Machine is easily positioned in the guided linear clamps, as well as the screening starts instantly having a “One Touch” go button. The built-in microprocessor regulates all the essential guidelines like pulling force, pulling speed and hold time. This allows for any completely controlled test each time.
The machine can be linked to an outside Computer, which enables usage of all programmable guidelines and configurations. The device is adapted to stand-on your own use or the incorporation into various subsystems. The machine posseses an substantial ability of logging and saving information including tugging force, pulling speed and fiber diameter along with other parameters.
Two recoat injector configurations can be purchased. The PTR307 uses an automated water pump to inject the recoat material. The volume of material dispensed through the automatic injector is managed by hand via the top-installed “Inject” switch or programmed to the machine utilizing the tablet pc control. The PTR307B features a handbook recoat injection program that will require the consumer to manually dispense the recoat material in to the mold cavity; a replacement injector for your PTR307B recoater is accessible below. Make sure you note that this automatic injector is simply appropriate for high-directory recoat material, while the handbook injector works with each reduced- and- index recoat material; they are both marketed separately below. Please get in touch with Tech Assistance to learn more.
he manual injector can be mounted to suitable SZ Stranding Line through the 4-40 anchoring screws on the recoater real estate (see photo for the right). Utilize a 3/32″ hex key to secure the injector before use. To connect the PTRRRM for the recoater mold, tighten up the connector at the end of the eco-friendly plastic material tubing, then release with a 1/4 consider allow for rotation.
The injector is equipped with a distribution valve and 2-position selection lever for directing the flow of recoat material. A knurled dispensing attach with an inner plunger acts as a syringe for the recoat materials. To fill the syringe, point the lever downwards (i.e., toward the recoat container), then spin the knurled dispensing screw counterclockwise until it rotates freely to fill up the syringe (shown inside the photo towards the right). Then, to inject the recoat materials to the mold, point the handle horizontally (i.e., dealing with the knurled screw) and spin the attach clockwise till near the end from the travel range is reached. Steer clear of bottoming out iuwekk dispenser as this may harm the interior plunger; also be careful when re-interesting the threads to avoid go across threading the dispensing screw. Several fill/inject steps may be required until air is displaced inside the system. Use camera lens cells plus an acetone or alcoholic beverages cleansing solution to accumulate any extra recoat materials that runs through the mold.